Linksys Tip: Assign Static IP Address To Printer While Using DHCP On Your Wireless Network

What Next?

How do I configure my static IP address?
Set up the Advanced Schedule Entry. Start with search, at the top of the page. Names that have a dot, like "foo. An 18 year career as a programmer at Microsoft soon followed. BlueGreen2 [pic] Scott D.

List of Routers with default IP address 192.168.0.1

192.168.1.1

Some implementations may be good for displaying simple static SVG, but may not support all features needed by Tomato. Inside or outside of the DHCP range will work, but it's probably better to use an address outside of the range so it doesn't get in the way. If you don't want to use static DHCP, you can still use the page by entering Names that have a dot, like "foo.

Undotted names like "foo" use the router's domain name. Multiple names may be entered by separating them with spaces foo1 foo2. The hostnames should work on all computers connected to the LAN as long as the router's DNS forwarder is used the default setting.

They will not work from the Internet side. The most common setup is to simply use a straight port forwarding like the following examples: Forward a single port: This is a type of port forwarding where external ports are only opened if data is sent to a trigger port from your computer. Firewall Protection -- Firewall is always enabled in Tomato.

Block Cookies, Port Scan -- Not supported. These options are not supported in Tomato. They are actually labeled a little bit incorrectly in Linksys' firmware: When disabled, ports are blocked. When enabled, they did nothing. If it worked before with the Linksys firmware when the "passthrough" was enabled, they should work fine under Tomato without any additional settings.

They can also be configured to do other tasks like running a custom script. Check with your DDNS provider's help pages for the exact format. It's the same type of URL that you can enter in your regular web browser. Basic authentication can be entered using the "http: POST requests are not supported. You can use "standard Linux commands. But keep in mind that only a few are included and most are simplified Busybox versions.

Some interesting utilities to play with: The startup script runs at startup or when the router is soft-restarted. The shutdown script runs when the router is shutdown, rebooted, or soft-restarted.

The first argument passed to this script is the number of seconds the button was held. It will also run at startup so the initial position can be read see example on how to avoid running at startup. The first argument passed to this script are the words "auto" or "bridge".

The startup script actually runs ahead of some services. Things that involve networking, for example, are not going to be up yet when the startup script begins. The client is very simple, written in Python and free. Go here to download it. You can also control how often you are polled for your IP address.

You can download the Beta client from here tzosetup. You can also download the source code, too! The logging mechanism added in V1.

If you're not happy with the Windows logviewer. Go here for a list. Also see the Tools page for alternative logging applications, written specifically for Linky. Linksys has made a newer version of logviewer. Doesn't come with any documentation or help, but you just run the. The new version lets you Empty clear and Save logs as well as display them. Reader Pete Jacoby got around this by booting into Safe Mode without network support and installing logviewer.

The information below was supplied by Linksys:. The reason forwarding is disabled is to test the SPI and make sure forwarding is not a factor.

In the released version, forwarding will not be disabled when SPI is enabled. The SPI feature can be tested by using applications like Netmeeting and other applications that use many ports dynamically. SPI will open the ports as needed as long as the data transfer session originates from a LAN side computer.

When the initial data transfer comes from the WAN side of the router, the normal port Forwarding feature must be used however, remember that Forwarding is disabled in the BETA. The Triggered Port button on the Forwarding page brings up a screen where you enter a trigger port range and incoming port range for up to 10 applications. This is basically a manual version of SPI.

The trigger port ranges are monitored and the incoming port range enabled when a data transfer using those ports is detected from a LAN client. The ports are opened only for the transfer, then closed again. Here is an article from Symantec's Knowledge Base that describes the problem:. In order to connect to pcAnywhere hosts that are behind routers using Network Address Translation NAT , there are two things that you need: A routable IP address for the Host. Refer to the document How to determine the IP address of a pcAnywhere host for additional information Port forwarding to forward ports TCP and UDP If port forwarding does not resolve the problem, you may need to update your router's firmware.

When you first open the configuration utility, you will be taken to the Basic Setup page. You can leave all of these settings at their defaults, unless specified otherwise by your ISP. This section will allow you to create and secure your wireless network. It is important that you change it from whatever default it was set to for security. Give your network a name. This is the name of your network, which will appear in the list of available networks for your wireless devices.

This essentially turns on your wireless network and allows it to be discovered. Here you will be able to set the security encryption type and password. This is the latest for of encryption, and the most secure way you can protect your network. Passphrase — This is the password that people will need to enter when they attempt to connect their devices to your network.

Make sure that the password is strong to prevent unwanted intruders. Your router will apply the changes and restart. Your wireless network will now be activated and secured. To check the IP address of your computer, see this guide.

To see a list of devices connected to your router and their respective IP addresses, click the Status tab and then select Local Network. Enter in the port forwarding information. In the Application field, enter the name of the application. Choose your starting and ending port. Only type in a port if instructed to by the application. Open ports can pose a security threat to your network. If you are unsure, select Both. Enter the IP address that you are forwarding the port to.

This is the address for the device that is running the application. You will only need to enter the digits from the last group of the IP address.

Enable the port forwarding. Open the Access Restrictions tab.

Preparation before login to Router

Leave a Reply